Multi-Link SR-3 Betriebsanleitung

SR SeriesSelective Ring ProcessorOnline OperatingInstructionswww.multi-link.net

InstallationYour SR Call Processor, when properlyinstalled and configured, can link together avariety of telephones and datacommunication products, in

2)3)Do I need barge-in protection?If you use a data device (FAX, MODEM, etc), Vyou should place the “BARGE-IN” switch in the “ON” position.Foryour SR

You will need to apply power to your SR with thesupplied AC adaptor. Be sure to pick an installation Vlocation where a grounded 110VAC power outlet is

Single LineInstallationA. Simple Plug-In(one jack, extensions)Ring Supervision: ExcellentBarge-in Protection: ExcellentInstall, Ease/Expense Excelle

B. Wiring ModificationsRing Supervision:Barge-in Protection:Install, Ease/ExpenseExcellent VExcellentDifficultMaterials Needed: 2 modular wall jacks,

3) If you disconnect the incoming line from a jack, label the existing jack“TELEPHONES”. If you did not, install a jack, label it “TELEPHONES”, andcon

C. Installation with Adapters:(only for use in homes where only one line isused, and each jack has four wires attached)Ring Supervision: ExcellentBarg

4) Connect the “DEVICE 1” jack of your SR to the “LINE 2”side of the 2-line adapter with a line cord.5) Connect your data devices and/or other telepho

Partial Supervision (cont)To Telephone Co.Central OfficeIn reality, this installation is fast, easy, and works great if you don’t needbarge-in protect

E. Total Supervisionwith Multiple SR’sRing SupervisionBarge-in Protection:Install, Ease/ExpenseTo Telephone Co.Central OfficeExcellentNope!ExcellentIf

REAR./3 4 51) Barge-In Protection Switch2) Power Indicator Light3) Device Ports4) Telephone Line Connector Port5) 12 Volt AC Power InputFRONTREAR4 5 6

Multiple LineInstallationA. Before a Key SystemRing Supervision: ExcellentBarge-in Protection: ExcellentInstall, Ease/Expense GoodTO KEY PHONESYou can

4) If necessary, install an RJ-11 on theKSU side of this line. Connect the“DEVICE 1” jack to this RJ-11 with a line cord.5) If necessary, run addition

Commonly AskedQuestionsHow does the SR Series Call Processor work?The SR Series Call Processor recognizesthe ring pattern of incoming calls by countin

Why does my SR Call Processor repeatedly click-clickwhen I pick up the line?If you cannot get a dial tone, and only hear a click-click every two secon

AppendixRecommended Partsand MaterialsMany electronics supply houses carry mostof the parts and materials you may need to modify your site wiring fori

Technical SpecificationsDimensions: 5” WWeight: 11.2 ozs.7%” L86 tiShipping Weight: 2 IbsInput Power RequirementsAt AC Transformer: 110-125 Volts AC

telephone number is called . In most, but not all areas, the sum of the RENsof all devices connected to one line should not exceed five (5.0). To bece

The SR Series Call Processor contains patented and otherwiseproprietary circuits and software algorithms. This owner’s manualdescribes the operation a

Contents12345678Introduction/How the SR Cal1 Processor Works...2Features and Applications...4Safety

Introduction/How theSR Call Processor Works 1Congratulations! You are now the owner ofthe highest quality Selective Ring CallProcessor on the market -

How The SR Cal1 ProcessorWorksThe SR Call Processor counts the number of bursts in the ring pattern ofthe telephone number called. It then directs the

Features andApplicationsThere are many applications for your SR CallProcessor in the home or small business. Tooptimize the phone configuration that i

APPLICATIONSThe advantage of call routing is to allow you thecapability of upgrading or modifying yourcommunications network as your needs change. He

SafetyInstructionsRead These Instructions !!!When using your SR Series Call Processor,basic safety precautions should always befollowed to reduce the

11. Never push objects of any kind into this productthrough cabinet slots as they may touch dangerous Vvoltage points or short out parts that could re